使用要求
组成部分：本机主要由机架部分、压榨部分、驱动部分、加热部分等组成，鉴于环保及循环利用意识，进料/收料装置可用饮料瓶等代替，故于用户自备。
组 装：使用前应将机架进行固定，固定时确保手柄能自由转动，之后将减摩垫圈浸上少许植物油套在榨螺小端，装入机架的榨膛中，与手柄连接并用螺栓固定，再将接头旋紧到榨膛上，调节螺塞拧入接头上.
燃料瓶中注入80%左右的燃料（煤油或酒精），将约15cm灯芯穿入挡片中，露出约0.5cm，之后将灯芯长端放入燃料瓶中，挡片放置瓶口，将燃料瓶置于机架集热罩下端，并用橡皮筋固定。
加 热：为保证出油效果，一般在榨制前需对榨膛进行预热约10分钟，榨膛温度到50－70℃后再在进料口加入原料进行榨制。榨油过程中需要持续加热。
操 作：确保压榨前原料中没有杂质异物.
压榨开始，少量油从调节螺塞处流出属于正常现象。
如果油饼过干或者手柄转动阻力过大,放松调节螺塞。
如果油饼中油残留过大，加紧调节螺塞。
清 理：使用后应及时清理，否则机器内残留物硬化影响下次的正常使用。
安全警示：由于物料的自摩擦产生的热能及燃料瓶的加热，造成机架榨膛及接头、调节螺栓温度较高，应避免与高温部分接触，如的确需操作高温部件请采取合理的防护措施。
声 明：随着技术进步，公司产品在不断更新。恕不另行通知产品变化。
Operation requirement:
Components: This machine consists of frame, press part, driver part and heating part etc. In view of environmental protection and recycling, material feeding/collecting equipment can be replaced with drink bottle, which is prepared by buyer.
Assembly：Before operation please fix the frame and make sure crank can be turned freely.
Lubricate washer with edible oil and insert on screw shaft from the small end.
Insert screw shaft in press cage.
Screw on press cage cap and screw on terminal adjustment bolt.
Attach crank arm to screw shaft and tighten the bolt.
Fill 80% fuel to the lamp bottle (kerosene or alcohol). Pass a 15cm wick through the washer. Leave 0.5cm of wick outside and put the longer end in the fuel bottle. Place washer at the bottle mouth. Place the lamp under press cage. Secure the lamp with rubber band.
Heating: To guarantee the oil output, the press cage should be heated for about 10 minutes. when the press cage temperature reaches 50－70℃, material can be put into inlet for pressing. The lamp remains heating during pressing as well.
Operation: Make sure no impurities in the material before pressing.
At the beginning of pressing, oil flowing from the terminal adjustment bolt is normal.
Loose the terminal adjustment bolt if the discharged cake is too dry and crank turning resistance is too big
Tighten the terminal adjustment bolt if the discharged cake contains too much oil residual.
Cleaning: Clean the oil press immediately after operation. Otherwise residual in the machine will get hard and affect next operation.
Safety and warnings
Material friction and lamp heating cause very hot press cage, press cage cap and terminal adjustment bolt. Keep hands clear of the hot parts. And if you indeed need operate the hot parts please take reasonable protection steps.
Notes: With technology renewal our product is improved continuously. We are not liable for informing buyer about product change in future.
配件名称：
- 手柄 crank
- 燃料瓶 fuel bottle
- 机架 frame
- 榨螺 screw shaft
- 榨膛press cage
- 接头 press cage cap
- 调节螺塞 terminal adjustment bolt
更多的操作细节，请关注我们的专业视频。
http://www.jmkzhayouji.cn/shipin/